Install the vinyl corners using at least a two foot level (preferably a six foot level) to make certain the corner goes on plumb. The corners should be installed ¾” below the fascia. To do this use a level on the fascia and mark it level against the wall. Measure down 3/4″ on the wall and drive a nail to indicate the level of the top of the corner. Slide the corner up to the nail. The corner should extend below the siding on the bottom by about 1/2″. If using wide corners it is advisable to step back from the corner and use your eyes to make certain that the nailing flange edges are not pulled too tight or not enough, which will cause uneven installation.
Something to consider prior to installing the siding is how to overlap the siding (joints). Vinyl siding looks much better from one side than the other, so if your driveway and deck are on the right of the house you will want to start the siding on the left side of the house. This will allow the siding installed on the right to overlap the siding on the left, which makes the siding joints less obvious. Install the first row of siding along an entire wall and using a chalk line snap a line along the top of the nailing flange to confer that the siding is going on straight. This should be performed about every five rows. When positioning the siding make certain that it snaps into place and nail into the centre of the nailing flange (working from the middle of the piece of siding to the edges) and leave the siding nail out 1/32″ (don’t drive the nail tight to the nailing flange. The entire sheet of siding must move left to right freely as a twelve foot piece of siding can expand and contract 1/2″ at different temperatures.). Remember that the first and last rows of siding are the most critical, so spend extra time on these areas.
As you work to near the top of the wall J-trim will be needed to receive the siding. Prior to installing J-trim it is a good idea to install the F-trim, which will receive the soffit. Place a two foot level up against the bottom of the fascia and extend it to the wall. Using a pencil or marker place a mark at he top of the level on the wall. Measure 1/2″ down from that mark to indicate the location of the bottom of the F-trim. Do this on each end of the wall and using a chalk line snap a line. Install F-trim (nailing flange up) with the bottom lining up to the chalk line and extend it over the vinyl corner.
After the F-trim is installed run the J-trim along the bottom of the f-trim (nailing flange down) and install undersill in the J-trim to hold the siding in place. Extend the J-trim and undersill to the corners.
If the windows and doors have a brickmould (trim) that is precut there is no need to install J-trim around these, the siding will slide into the brickmould. If the brickmould is enclosed a utility knife can be used to remove the strip of vinyl on the sides. Start by cutting the corner along the house and then insert the knife blade into the slot at the front of the brickmould. Once a 12″ section is cut it is possible to cut the strip and pull the remainder out by hand. This is easier than trying to cut the slot the entire length of the trim. Use pliers if available to help pull the trim.
For more information visit Halifax Gutters, a division of Rondon Group Ltd.
Article Source
Garage kits are a great way to easily and affordably add a garage to your home; garages are used every day by homeowners who have them and those who don’t are often wishing they do. If you have made the decision to add a garage to your home using a garage kit you are one step closer to having a garage at your home. The difficult part may be finding that perfect garage kit for your home and determining how you want to go about having the garage assembled.
When you are selecting your garage kit it is important to evaluate the exterior of your home and how important it is to you that the two builds are cohesive. Most garage kit producers or retailers offer garage kits in a variety of colors and styles it is just a matter of finding the right one for you. It is also important that you evaluate how many vehicles you need to park and how much additional storage space you’ll need before choosing your garage kit. By looking at many different garage kit options before making a purchase you will be able to make the purchase confidently.
Once you decide on the garage kit for your home it is time to decide who is going to build the garage. If you have experience building and completing home projects then you can likely build your garage on your own. But if you have never so much as picked up a hammer or drill then you may want to consider working with a builder. The company that you order your garage kit from may have a network of preferred builders for you to choose from but you may also have to conduct your own research. If your retailer has a preferred builder it is a great idea to go with them as they likely do great, trusted work; if you are looking for your own builder you may want to ask friends and family members for suggestions for builders.
Once you have your garage kit selected as well as your building method decided you will be on your way to having a garage at your home in no time. You will be able to enjoy the convenience of having covered parking along with extra storage once your garage is completely built. Get your kit order in today and find out just how convenient garage kits can be before winter hits and you may have to wait until spring to have the build completed
